A great question a from a homeowner in Alberta
Hi all,
This is our second winter in a newly built house. The basement was insulated with a layer of poly against the concrete and framing done about 2-3 inches off the wall. One layer of fiberglass batting is running horizontally and set in between the concrete/poly and the framing. A a second layer of batting is then running vertically between the framing for a total of two layers. There is then another layer of poly on the inside sealing it off. So it is concrete - poly - horizontal batting - framing - vertical batting - poly.
The problem is moisture has found a way in and there is considerable condensation between the poly and the horizontal batting. There is frost formation and it has condensed enough to seep out the bottom (which is how we noticed the problem).
I've opened up a few areas to assess, but am wondering what the best way to resolve this is? The ground will still be cold for another month or two (we're in Winnipeg) so I'm not sure if it's best to wait for things to warm up and the frost melts, or if this is urgent enough where I should start trying to rip out insulation now? A lot of insulation is actually frozen to that layer of poly on the concrete so it'll be messy.
Thanks for any advice.
This is a very common problem even here in Ontario
Below is my response to him.
I would leave it for now. let it warm up, then tear out all the insulation out and start fresh
Not sure of the National Building Codes for your area so you should find out before replacing materials to ensure it is completed correctly. I'm in Ontario so we use the OBC
You want an air barrier membrane against the foundation wall not a vapour barrier.
The poly vapour barrier only goes on the warm side of the insulation. What you currently have lets any warm air that enters the insulated area to condense and form water droplets and then freeze to the foundation wall. The warm air has nowhere to escape and gets trapped between the two layers of vapour barrier.
One area that is quite often missed and most likely is a cause for issue is to ensure when the new vapour gets installed that EVERY SINGLE entry point for warm air is either taped, and/or acoustic sealed. This includes the header area especially. No warm air behind the vapour barrier means no moisture/water damage.
A little reading that may help with understanding some correct ways to insulate
http://www.mah.gov.on.ca/Asset8275.aspx?method=1
Hope this helps answer some questions
Dave 360renos.ca
How to make your home stand out when selling
We can help your house sell quickly and at a good price -- even in a slow market.
It takes a lot more than sparkling windows, scented candles and chocolate-chip cookies to sell a home in today's market.
Improvements should be made so that the property shows well, is consistent with the neighborhood and does not involve capital investments.
Beyond any doubt, the best investment you can make is new paint. Painting can make a room or an exterior façade look brand-new, and totally transform the look and feel of a room or the entire residence. It is always wise to be somewhat restrained when choosing colors for a home-staging paint project. Avoid choosing colors that are too individual or flashy and favor neutral colors and schemes. This does not mean painting everything white, however.
Use subtle color schemes to accentuate the home's strengths and minimize weaknesses. Dark colors, for example, tend to make a room feel smaller, while lighter colors and pastels can make a room feel bigger.
There is another benefit to painting as well: the process of preparing the interior or exterior surfaces of a home for painting automatically allows us to go over the entire area receiving paint in great detail, and this can often expose items or areas requiring repair. It seems you always discover where the caulking has let go, where the wall is dinged.
It is always preferable that we discover and deal with these items before the real estate agent (or worse, the prospective buyer) points them out to you!
Dave - 360renos
It takes a lot more than sparkling windows, scented candles and chocolate-chip cookies to sell a home in today's market.
Improvements should be made so that the property shows well, is consistent with the neighborhood and does not involve capital investments.
Beyond any doubt, the best investment you can make is new paint. Painting can make a room or an exterior façade look brand-new, and totally transform the look and feel of a room or the entire residence. It is always wise to be somewhat restrained when choosing colors for a home-staging paint project. Avoid choosing colors that are too individual or flashy and favor neutral colors and schemes. This does not mean painting everything white, however.
Use subtle color schemes to accentuate the home's strengths and minimize weaknesses. Dark colors, for example, tend to make a room feel smaller, while lighter colors and pastels can make a room feel bigger.
There is another benefit to painting as well: the process of preparing the interior or exterior surfaces of a home for painting automatically allows us to go over the entire area receiving paint in great detail, and this can often expose items or areas requiring repair. It seems you always discover where the caulking has let go, where the wall is dinged.
It is always preferable that we discover and deal with these items before the real estate agent (or worse, the prospective buyer) points them out to you!
Dave - 360renos
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment